top of page

Aluminum VersaLite

SABINE-FA23-20231129-CMB104386 Versalite Tiller.jpg
Length Overall – 18′-0" | Deck Beam – 68″ | Recommended Horsepower Rating - 40-50

Standard Features

  • Sabine Tiller VersaLite - 18' LOA 68" Beam aluminum poling skiff hull

  • Basic Rigging - front and rear dry storage hatch, 15 gallon built-in fuel tank, under gunnel rod holders facing Aft, 6 rod tubes, black heavy duty rub rail, Odyssey 1200 Cranking Battery, Battery on/off switch, Blue Sea 12 panel fuse bank, 800 Rule bilge pump w/ switch, Pop-up cleat on fore deck, hull painted (1) color customer's choice, Standard poling platform w/ Seadek, Seadek cockpit floor and VMarine push pole holders

  • McClain HD Aluminum Trailer - torsion axle, 14" aluminum rims, led lights and SS Boatbuckle tie downs

Popular Features

Skiff Options

  • Two color - Hull and deck are different colors

  • Cup holder

  • 3/16" bottom upgrade

  • Tunnel hull

  • Stand-up Grab Bar w/ motor tilt/trim, jackplate and Lenco switches mounted to the grab bar

  • Tiller pod console - gps will be flush mounted and all switches will be mounted on the console

  • Bob's Micro Hydraulic Jackplate - installed

  • Large front casting platform with Seadek and SS tie-down hardware 

  • 10" Light bar mounted on casting platform 

  • Poling platform grab bar - removable 

  • Casting platform grab bar - removable

  • Lenco trim tabs w/ single switch

  • Lenco trim tab switches on grab bar and poling platform

  • Powder coated Parts (black) - poling/casting platforms, nav lights, pop-up cleat and latches

  • (2) LED under gunnel lights 90" and switch - RGB; green, red, blue or white

  • USB Power plug mounted inside storage compartment 

  • 12V Power plug

  • Fire Extinguisher - installed

  • Vmarine Push pole Platform Holder - installed

  • Seadek - front deck, rear deck and gunnels 

  • Seadek cockpit 6mm upgrade

  • Seadek full under gunnel w/ Sabine logos - one color

  • Seadek bow deck lid with Sabine logo

  • Cooler tie-downs installed

  • Yeti Tundra 65 or 45 quart cooler

  • Stiffy Push Pole - Hybrid, Guide or Xtreme

  • Trolling motor installed - circuit breaker, cables, trolling motor quick release, Battery Tender cable quick release, terminated and installed - Customer to provide the trolling motor, battery and tray

  • 4' or 6' Power-pole ProSeries II, installed - black or white

  • GPS Transducer Install 

  • GPS Install - Customer to provide 9" or 12" GPS

Motor Options

  • Custom Baumann 3 blade propeller

  • Custom Baumann 4 blade propeller

  • Tohatsu factory white

  • Custom painted motor - Awlgrip finish

  • Tilt/trim on bulkhead

  • Tilt/trim switch on grab bar or tiller pod console

  • Tilt/trim switch on poling platform 

  • Jack plate switch on bulkhead

  • Jack plate switch on grab bar

  • Jack plate switch on poling platform 

  • Carbon Marine tiller extension

  • Analog fuel gauge

  • Motor digital gauges

  • NMEA fuel sender ran to digital gauge or GPS

  • Motor NMEA harness for motor read out on customer's GPS

Trailer Options

  • Swing tongue

  • Blacked powder coated fenders

  • Trailer Spare Tire and Bolt-on Kit (Aluminum)

© 2024 Ultralight Boatworks, LLC
bottom of page